Product Overview
This contactless dispenser is manufactured as per DRDO Specifications and can spray alcohol based hand rub sanitizer for sanitization of hands while entering buildings like Hospitals, Office complexes, Malls etc. This is a mist based dispenser, to optimize the consumption of sanitizer,by dispensing just 5-6 ml of sanitizer at a time, in mist form over a longer period of time ensures that the hands are covered completely . Technical Specification: i) Sanitizer Storage capacity of the unit: 5L ii) Mode of operation: Automatic Mist mode iii) Usage: Contactless iv) Weight : 5 kg (without sanitizer) v) Dimensions: 45 cm (H) X 30 cm (W) X 22cm (D) vi) Electrical Input - 230V AC, 5 Amp vii) Power Consumption: a) Idle Mode - < 3VA b) When Spraying - 25VA approx. viii) Mounting Style - Wall mount Main components:- 1. Outer Body - ABS 2. Sanitizer Container is of sturdy construction in ABS, where the sanitizer is stored/refilled Capacity - 5 Litres 3. The dispenser is provided with good quality Solenoid Valve in Polyprorylene body to prevents dripping of water to drip from the nozzle when pump is not working, Working voltage - 24V DC 4.A Diaphragm pump in ABS body, is used to provide increased pressure to the inlet of the mist atomizer. Working Pressure - 5-6 bar,IP Rating - IP 54,Working Voltage - 24V DC 5. Mist Atomizer - This atomizer sprays sufficient amount of sanitizer at a cone angle of 60a to wet both the hands for pre set duration of time Material -Brass , Sanitizer Discharge - 5-6 ml for each operation 6. Waterproof non contact ultrasonic sensor , Epoxy filled in ABS body - This module, with air as medium, is a non-contact target detection and distance measurement module. This sensor is not affected by color or other visual from the detected object. Min sensing distance a 2o mm Max hand distance - 200 mm 7. Switch Mode Power Supply (SMPS)- The power supply unit (PSU) in ABS body is used in the unit to convert the AC voltage into the acceptable range for working of the pump and solenoid valve. This device has the power handling electronic components that converts electrical power efficiently. Inpuut Voltage 210-230V AC, Output - 24VDC, 2Amp 8. Control Circuit a Algorithm configuration: Once the hand is detected it switches on the dosing pump for a preset period of time.
This contactless dispenser is manufactured as per DRDO Specifications and can spray alcohol based hand rub sanitizer for sanitization of hands while entering buildings like Hospitals, Office complexes, Malls etc. This is a mist based dispenser, to optimize the consumption of sanitizer,by dispensing just 5-6 ml of sanitizer at a time, in mist form over a longer period of time ensures that the hands are covered completely . Technical Specification: i) Sanitizer Storage capacity of the unit: 5L ii) Mode of operation: Automatic Mist mode iii) Usage: Contactless iv) Weight : 5 kg (without sanitizer) v) Dimensions: 45 cm (H) X 30 cm (W) X 22cm (D) vi) Electrical Input - 230V AC, 5 Amp vii) Power Consumption: a) Idle Mode - < 3VA b) When Spraying - 25VA approx. viii) Mounting Style - Wall mount Main components:- 1. Outer Body - ABS 2. Sanitizer Container is of sturdy construction in ABS, where the sanitizer is stored/refilled Capacity - 5 Litres 3. The dispenser is provided with good quality Solenoid Valve in Polyprorylene body to prevents dripping of water to drip from the nozzle when pump is not working, Working voltage - 24V DC 4.A Diaphragm pump in ABS body, is used to provide increased pressure to the inlet of the mist atomizer. Working Pressure - 5-6 bar,IP Rating - IP 54,Working Voltage - 24V DC 5. Mist Atomizer - This atomizer sprays sufficient amount of sanitizer at a cone angle of 60a to wet both the hands for pre set duration of time Material -Brass , Sanitizer Discharge - 5-6 ml for each operation 6. Waterproof non contact ultrasonic sensor , Epoxy filled in ABS body - This module, with air as medium, is a non-contact target detection and distance measurement module. This sensor is not affected by color or other visual from the detected object. Min sensing distance a 2o mm Max hand distance - 200 mm 7. Switch Mode Power Supply (SMPS)- The power supply unit (PSU) in ABS body is used in the unit to convert the AC voltage into the acceptable range for working of the pump and solenoid valve. This device has the power handling electronic components that converts electrical power efficiently. Inpuut Voltage 210-230V AC, Output - 24VDC, 2Amp 8. Control Circuit a Algorithm configuration: Once the hand is detected it switches on the dosing pump for a preset period of time.
Contact Now
Company Profile